If you want something more modern than a typical deadbolt or lock and key mechanism to secure your door, you should check into magnetic and electric lock options. They’re available in a range of forms and sizes. Companies design these locks for specific use and door layout. There are many tutorials that go through the many types of locks available and which ones might be best for you. In this article, we’ll go over magnetic door lock tectus, installation advice, and how to utilize it on a daily basis.
What Is A Magnetic Door Lock Tectus And How Does It Work?
We’ll look at the technology behind a magnetic door lock tectus and how to install it in this part.
A Magnetic Lock's "Moving Parts"
Magnetic locks are often known as maglocks. These locks comprise two major components: a mounting mechanism and wires. Locksmiths install these two components such that their magnetic sides face each other on the frame and door. If your door frame or door does not allow direct mounting, the mounting plate can be attached. Professionals attach these wires to the lock and run along or through the walls to a specialized power supply to provide electricity to the magnet.
Contact a Commercial locksmith in Melrose Park for more information and services.
Fault-Tolerance Mechanism
Maglocks have a fail-safe system in place. When the lock receives electricity, the magnet is engaged, and the two parts (one fastened to the wall and the other to the door) get stuck firmly, keeping the door secured. The electricity is cut and the door unlocks when the lock is triggered.
How To Put A Magnetic Door Lock Tectus In Place And Unlock It
Fail-safe locks are useful for emergency routes because it’s more likely that the electricity will be out in an emergency. You would like to be able to open the door in those situations. Many businesses choose to install a magnetic door lock on their front doors for this reason.
How To Set It Up
Drill holes in the wall and the door to screw in the lock, and run wires through the wall to link it to a permanent power supply when installing a magnetic door lock tectus.
The Schlage 400 series maglock is a good all-around lock, and you can find thorough installation diagrams for all configurations on this website. They all have the same basic structure: Drill the holes, attach the brackets to hold the locks, run the wires, turn it on, and test it.
How To Put It To The Test
Testing the lock is a crucial step in any installation.
You can’t truly consider the lock installed until you’ve given it a test drive and checked to make sure it unlocks properly, whether you’re bold enough to do it yourself or hire an installer to do it for you.
This is a rather simple procedure to follow. After connecting the electricity, you’ll need to verify the lock’s unlocking capabilities using whatever access system you have on hand. When the lock is in its functioning, it should tightly close the door. However, when the power is turned off, the lock should open.
Precautionary Measures:
Aside from adequate functionality, there are a few things you should check for in this type of installation.
Fire Compliance
The first is fire compliance: Fire laws vary by city and building type. You may need to install a motion sensor, contact sensor, or request-to-exit button. Check out the article on this site for more information on fire codes and fire safety.
On the subject of emergency circumstances, you might want to consider installing a manual override key in your door. Despite the fact that this is a fail-safe lock that allows you to depart even if the power goes out, there may be a problem inside the lock that stops it from opening at a critical moment. A backup key might be handy in this situation. This is something you should discuss with your installer or integrator. In case of emergency, contact any company which provides a 24-hour locksmith.
How Does An Access Control System Unlock A Magnetic Mortise Door Lock Tectus?
We’ll go through the basics of how these magnetic locks function with current IP-based access control in this part.
Wiring
You need to wire the Magnetic door locks to the access controller to know when someone tries to open forcefully just as they must be charged by electricity. The fail-safe nature of these locks means that when they are triggered, they lose their ability to unlock. The controller will temporarily cut the power ( you can manually program the amount of time). Moreover, the door will open when the access control readers send an impulse to the lock.
Wiring For The Lock, Power Supply, And Access System
There is a specialized lock power supply as well as a separate controller power supply. Locksmiths wire the controller to both the lock and the lock’s power supply. Thus, we can allow it to stop the power when the door needs to be unlocked.
Unlocking
The process of Unlocking depends on the mode of access you chose, just like wiring and most other aspects of these locks. Moreover, Unlocking your door will be as simple as touching your phone (or a keycard) to the reader next to your door. However, this will only work if you have properly installed wiring and you’re using a modern IP-based access control system.
The reader will then send a Bluetooth or Wifi signal to the controller, which is the operation’s brain. It will authenticate the signal, determining whether the user has access at that particular time. If this is the case, the controller will send an impulse via the wire to the lock power supply, cutting off that power for a brief period to unlock the door.
Conclusion:
Magnetic locks are dependable and adaptable locks. We should only use them as the primary means of admission and egress in any office. They are perfect for emergency scenarios when the power goes out since they have a fail-safe mechanism, and they can be connected with current access control for a seamless unlocking experience.