Sliding glass doors give a home a more open feel. They provide a clear view of the backyard, patio, or playground area. Opening a wooden door to look outside the house allows parents to observe youngsters at play much more comfortably. Although these doors are convenient, your locks will need to be clean, lubricate, and adjust from time to time to keep them secure. And you should also need to repair the sliding glass door.
However, even with all the attention, they might break or cease working, necessitating maintenance. The technique is most likely not the same. As a result, it’s critical to remember that we’re dealing with glass here. Call Lock repair and replacement in Chicago to repair your sliding glass door properly.
Steps For Repair Sliding Glass Door Lock
- To open the door, turn the round door lock inside the sliding glass door jamb.
- Depress the pressurized air can’s trigger. Direct the jet into the edge of the door’s lock. Dirt, debris, or foreign objects is the reason for blocking the sliding door lock. You will remove any debris by spraying the lock with high pressure.
- Spray a generous amount of spray lubricant on the sliding door’s closing door near the edge. After a minute, reapply the lubricating spray on the latch.
- Turn the locking knob right and left to see how the door closes. The lubricating spray allows the latch to retract fluidly into the doorjamb and lock.
- With a little flat screwdriver, loosen the lock plate screws in the door jamb by rotating them counterclockwise.
- Close the door almost completely and check the lock level on the latch.
- To accept the lock in the strike plate’s center, move the strike plate lock up or down.
- With one hand, the plate retention latches in place and tightens all screws clockwise.
- However, close the glass sliding door. To test the repairs, turn the knob to the lock position and try to pull the door open. When the door is in a locked position, it should not open.
Repairing Or Replace The Sliding Glass Door Lock
When inexpensive sliding door locks are uninstalled, they often break permanently. On the other hand, a mortise lock is designed to be serviceable. However, The lock must be built to detach and reassemble to repair sliding door locks.
If your sliding door has a mortise lock, the lock body will slide out of a pocket carved into the door. However, The lock body can then be opened for more thorough cleaning or to check for broken springs or actuators. With an inside view of the lock, you can see what needs to be repaired more clearly. It’s similar to removing a broken key from a lock when it comes to clearing jams. To clear obstructions, you may need to tweeze and pry at debris or stuck lock components. Call Lock repair and replacement in Elmwood Park for affordable and proper installation of your sliding glass door lock.
Replacing minor parts may be difficult for antique locks because not all parts are likely to be available. Furthermore, many new sliding door locks do not have readily available replacement parts. Only locksmiths who have cannibalized partially broken locks may have spare parts.
When Should You Replace Your Sliding Glass Door Lock?
Sliding doors are equipped with handles that are secured by latches. Many come with keys that can be used to lock and unlock the doors from the outside. If you lose your door key, you should change the locks as a precaution. You will be changing the door locks on the sliding glass doors. Replace the handles on any doors with the same key.
Instructions
- Open the sliding glass door on both sides to reach the handle. Depending on the screw type, remove the screws securing the door handle using a Phillips or slotted screwdriver. On all sides, pull the handle apart. Remove any door handles that require replacement locks.
- With a ruler, measure the distance between the screw holes. Measure the length and width of the slot that goes into the door frame’s recessed handle. You should measure the thickness of the door frame. When purchasing replacement handles, ensure that all sizes are the same.
- Place the new handle in the door frame aperture or bare screw holes. Tighten the screws after they’ve been placed in the holes. Hand them in to assist them in starting in the threads on the handle’s outside. Tighten the screws firmly with the suitable screwdriver.
- Drag the closed door open, lock the lock, then try to open the door to view the new lock.
Warnings and Suggestions
- Sliding glass door locks that aren’t protected from rain, snow, or the elements might become stuck anywhere.
- After lubrication, opening and closing the lock helps the oil penetrate deep into the locking mechanism.
- Installing a sliding door necessitates a 1/8-inch gap between the doors rather than a 1/16-inch gap.
- When the spacing is less, the door becomes too tight, and the glass will break as the door is secured.
Conclusion
It’s critical to repair sliding door locks, so your home’s security isn’t at risk. Even though sliding doors do not give much protection, all effective crime prevention measures require that all locks be in functioning order, especially on outside doors.